LED flashlight Fenix PD25R

Parameters of the Fenix PD25R flashlight

• It uses a premium Luminus SST-20 LED with a lifetime of 50000 hours.
• Six lighting modes: 800 lumens (44 minutes) -> 350 lumens (1.5 hours) -> 150 lumens (2.8 hours) -> 30 lumens (16 hours) -> 5 lumens (70 hours) -> 800 lumens strobe
• Endurance times are measured with charging Li-ion battery type RCR123A with capacity 700 mAhwhich is included in the package.
• Max. battery diameter 16,9 mm, max. battery length 37,0 mm.
• A disposable can also be used for emergency power 3V CR123A battery, but the highest performance will not be available.
• Digitally controlled for constant brightness, intelligent overheat protection.
• Well-focused light cone with a range of up to 250 metres (15 530 cd)
• Dimensions 9,2 cm (length) x 2,4 cm (diameter).
• Weight 78 grams (including battery).
• Made of A6061-T6 type aerospace hardened aluminium.
• The flashlight has a memory and always switches on in the last mode setting (not valid for flash mode).
• Reversible clasp for hanging on pocket, visor or Molle binding.
• Durable surface - Type III hard anodized.
• Shockproof against falls from a height of 1 meter.
• Waterproof and dustproof according to IP68 standard (tested under water at a depth of 2 meters for 30 minutes).
• Tempered ultra clear glass lens with anti-reflective surface.
• Tactical switch at the end of the flashlight (momentary on/off function).
• The flashlight comes with a wrist lanyard, steel double-sided buckle, belt pouch and spare o-rings, Fenix ARB-L16-700P / RCR123A battery.
• As an optional original accessory the following can be purchased: aOD-S diffuser.
• The flashlight is also compatible with lampFix helmet mount, swivel wrist holder ALW-01, aB02 rotating sleeve, bike flashlight holder, bikeBlock bike helmet holder, fenix bike holder or replacement battery RCR123A with USB-C connector or replacement battery with higher capacity 950 mAh.

Use

There may be a battery inside the flashlight from the factory insulating cap. Before using it for the first time remove the battery.

For turn on press the tactical switch located at the end of the flashlight, press the button for immediate activation. Press the side button at the head of the flashlight to switch between power modes at any time during operation. To switch to strobe mode, hold the side button for approximately 0.5 seconds.

Charging - Unscrew the protective nut under the head of the flashlight and plug it into your computer using the included USB-C cable, uSB network adapter or USB car adapter (not included). Alternatively, any mobile phone charger with a USB-C connector can be used for charging. During charging, the indicator LED in the button is red, after a full charge it glows green. Charging a fully discharged battery takes about 2 hours. The Li-ion battery used does not suffer from memory effect, so the flashlight can be recharged at any time. During charging, the flashlight can only be lit in the lowest mode by holding the side button for 0.5 seconds.

Intelligent overheating protection - if the temperature of the lamp rises above 60°C, it will automatically reduce the power in gradual steps.

Battery charge indication - each time the flashlight is switched on, the indicator LED in the side button of the flashlight is activated for three seconds. If the indicator LED is green, the battery is more than 85% charged. Green flashing indicates 50-85% capacity. If it is red, the battery is 25-50% charged. Red flashing indicates less than 25% battery capacity remaining. (only works when using RCR123A / 16340 Li-ion battery)

Low battery warning - the flashlight automatically switches to the lowest mode, in the lowest mode the indicator LED in the button flashes red. This indicates the need to charge the battery or replace it with a fully charged one.

Notice

• Do not disassemble the sealed part in the head of the flashlight yourself, this will violate the warranty.
• Use only high quality CR123A or RCR123A batteries.
• If the protective rubber rings appear damaged after prolonged use, replace them. The rings should also be lubricated to prevent erosion of the